Electrical

12 volt, 2 amp power supply - $15
(w/ straight or right angle plug end).

12 volt, 8 amp power supply - $18

0-12 volt, 2 amp variable voltage power supply w/ digital display - $18

Micro Voltage Controller - $45
(bamboo and domestic wood). Exotic wood available for additional cost.
Plastic box version - $35
2” x 1.75” x 1.5” tall
Input - 5.5mm x 2.1mm socket, 5 to 30 volts DC (center positive)
Output - 5.5mm x 2.1mm jack, 1 to 30 volts DC (center positive)
25 watt capacity
Programmable start voltage
Digital voltage display
Short circuit protection
No slip feet
Micro knob adjustment

DC extension cord, right angle or straight plug end - $5
(Connects to micro voltage controller output jack).

Car adapter - $10

Screens

$0.50 each

6mm basket - fits 5/16” ss tubes. Heat Island, Underdog, PD, Zap.

8mm basket - fits 10mm glass tubes, 3/8” ss tubes. Heat Island, Dynavap.

10mm basket - fits 12mm / 13mm / 15mm glass, 7/16” ss, wood, silicone, and bamboo tubes with 10mm ID. Heat Island, Underdog , e-nano.

3/8” flat - fits 7/16” ss tubes. Heat Island.

10mm flat - fits turbo tubes, wood tube, and bamboo tubes w/ 10mm ID glass roasting tube. Heat Island, Underdog, PD.

12mm basket - fits 19/22mm glass and wood, 16mm glass on 14mm GonG tubes. Lil’ bud, timber elite, milaana, splinter, tinymight and tubo w/ 12mm ID tubes.

The roasting tube screen should be checked prior to each use. The screen should be free from debris and allow good air flow. There are several methods for cleaning the screen. Roasting, burning, and soaking are the most common. The material that builds up on the screen can be roasted by setting the screen on the end of the heater cover for a while and then brushed clean. The screen can be burned and then brushed clean. The screen should be removed from the roasting tube prior to burning. Alcohol can be used to soak the screen clean.

Cork

10mm tube connector, square sides, 1.75” lg. - $3

13mm tube connector, 0.875” lg. - $2

13mm tube connector, 1.75” lg. - $2

16mm tube connector, 1.75” lg. - $2

19mmt, 0.875” lg, 13mm hole - $3

19mmt, 1.75” lg, 13mm hole - $4

19mmt, 19mmt, 1.75” lg, 13mm hole - $6

19mmt, 1.75” lg, 13mm / 10mm hole (SAB) - $5

19mmt, 19mmt, 1.75” lg, 13mm / 10m hole (SAB) - $7

19mmt, Dynavap tip adapter - $5
Allows Dynavap tip to fit IH, LB, Mi, Splinter, Tubo, etc.

Silicone

Silicone Turbo Tube - $3

5/16” x 3/16” lg, connects 5/16” ss tube to 10mm ID glass tube - $0.50

7/16” x 1” lg, connector / sleeve for 5/16” ss tube - $0.50

7/16” x 3.5” lg, mouthpiece tube for silicone turbo tube - $1

7/16” x 24” lg, hose - $4

7/16” x 24” lg, cloth string covered hose - $14

1/2” x 3/8” lg, power plug cover and sleeve for 13m glass tube - $0.50

1/2” x 5/8” lg, connector for 10mm/12mm glass tubes - $0.50

1/2” x 3/4” lg, connector for 10mm/12mm glass tubes - $0.50

1/2” x 1.25” lg, Turbo Tube, Slide-a-Bowl tube, U-Tube - $0.50

5/8” x 3/16” lg, U-Tube - $0.50

5/8” x 3/8” lg, Air/Solo - $0.50

Accessories

Travel stir tool (bamboo skewer w/ sewing needle in end) - $5

Glass aromatherapy cup - $10

Small poly storage tube - $1 (10, 12, and 13mm tubes)

Large poly storage tube - $2 (14, 16, and 18mm tubes)

Beeswax beads - $0.50

Hemp fiber - $3

LSV

Pine wood stand for your LSV - $40
Two piece design for storage or travel.

3/8" ss LSV heater cover, 4.25” - $15
Use your LSV with all roasting tubes compatible with a 3/8" ss heater cover.

Wood Maintenance

Pure beeswax was applied to the wood during the creation of the Heat Island / Toasty Top / Insta Heat and should be periodically applied to the wood when it is looking dry. It may be applied with your fingers or a soft cloth. A hair dryer can be used to heat the wood so that the beeswax soaks into the wood. Beeswax can also be applied to the exterior of wood roasting tubes.